Heat Transfer Laboratory Equipment

Approx. Rs 70,000 / PIECEGet Latest Price

• To estimate the actual rate of heat transfer through the composite cylinders from the measured
• Interface temperature of the two insulating materials with known thermal conductivities.
• To determine the effective thermal conductivity of the composite cylinder
• To compare the theoretical temperature profile within the composite cylinders, with that of observed profile.

• Table For Set-Up Support

• G.I. Pipe Inner: 5 Cm Dia. Approx
• G.I. Pipe Middle: 10 Cm Dia. Approx
• G.I. Pipe Outer: 15 Cm Dia. Approx
• Heater: Nichrome Wire

Additional Information:

• Item Code: SHT-02
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A,Other
• Production Capacity: 100 units/month
• Packaging Details: Wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

• Determination of thermal conductivity of insulating powder
• Comparison of thermal conductivity of insulating powder at different temperatures

• Table For Set-Up Support

• Temperature Sensors: Rtd Pt-100 Type
• With Standard Make On/Off Switch, Mains Indicator Etc
• Instruction Manual: An English Instruction Manual Will Be Provided Along With The Apparatus
• The Whole Set-Up Is Mounted On A Power Coated Base Plate.

Additional Information:

• Item Code: SHT-04
• Production Capacity: 100 units/month
• Packaging Details: Wooden Carrots are used for Packaging if Required

Approx. Rs 45,000 / PieceGet Latest Price

DESCRIPTION:

consists of main central heater and ring guard heater, sandwiched between the specimens.  Cooling plates are provided on either side of the specimen.  Two identical specimens are clamped between heater that ensures unidirectional heat flow through specimen. The whole assembly is The set-up is designed to determine thermal conductivity of insulating materials in the form of slab. The apparatus kept in chamber and insulated by ceramic wool insulation around the set-up.

EXPERIMENTATION

Ø  Determination of thermal conductivity of insulating material in the form of slab.

Ø  Study of variation of thermal conductivity of the material with temperature.

UTILITIES REQUIRED

Ø  Water supply 5 lit/min (approx.)

Ø  Drain.

Ø  Electricity Supply: 1 Phase, 220 V AC, 2 Amp.

Ø  Table for set-up support.

TECHNICAL DETAILS:

Ø  Specimen

Diameter: 180 mm (approx).

Thickness: 12 mm (approx).

Ø  Central Heater: Dia 100 mm, sandwiched between copper plates.

Ø  Ring Guard Heater: Width 35 mm, sandwiched between copper rings.

Ø  Cooling chamber: Made of Aluminium for water circulation. 2 Nos.

Ø  Insulation: Ceramic wool

Ø  Control panel comprising of:

Digital Voltmeter: 0-300 Volt.

Digital Ammeter: 0-2 Amp

Variac: 0-230 V, 2 Amps, (2 Nos.)

One each for central & ring guard heater.

Digital Temp. Indicator: 0199.90C, with multi-channel switch

Temperature Sensors: RTD PT-100 type.

With standard make on off switch, Mains Indicator etc.

Ø  Instruction Manual: An ENGLISH instruction manual will be provided along With the Apparatus

Ø  MS Cabinet to accommodate the slab assembly.

Ø  The whole setup is mounted on a powder coated base plate

Additional Information:

• Item Code: SHT-06
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

• Determination Of Thermal Conductivity Of Liquid
• Study Of Variation Of Thermal Conductivity Of Liquid With Temperature

• Drain
• Table For Set-Up Support

Additional Information:

• Item Code: SHT-07
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / UnitGet Latest Price

• Temperature controller
• Power coated structure
• Insulated With Ceramic Wool And cladded By Aluminum Foil

• To Study The Film Wise & Drop Wise Condensation Of Steam On A Vertical Surface
• Visualization Of Condensation Process In Drop Wise As Well As Film Wise Condition

• Table For Set-Up Support

• Copper Tubes (2 Nos.): One With Natural Finish And Other Nickel Polished
• Water Flow Measurement: Rotameter
• Condensate Measurement: Measuring Cylinder & Stopwatch
• Control Valves: One Each For Steam, Cooling Water & Drain
• With Standard Make On/Off Switch, Mains Indicator Etc
• Instruction Manual: An English Instruction Manual Will Be Provided Along With The Apparatus
• The Whole Set-Up Is Well Designed And Arranged On A Powder Coated Structure.

Additional Information:

• Item Code: SHT-13
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden carrots are used for Packaging

Approx. Rs 31,000 / UnitGet Latest Price

• To calculate the biot number, Fourier number and hence the heat transfer coefficient
• To plot heister chart for the given sample of cylindrical solid

• With Standard Make On/Off Switch, Mains Indicator Etc
• Instruction Manual: An English Instruction Manual Will Be Provided Along With The Apparatus
• The Whole Set-Up Is Well Designed And Arranged On A Powder-Coated Structure.

Additional Information:

• Item Code: SHT-19
• Production Capacity: 100 units/month
• Packaging Details: Wooden Boxes are used for Packaging if required

Approx. Rs 33,500 / PieceGet Latest Price

• To determine total thermal resistance and thermal conductivity of composite wall
• To plot temperature gradient along composite wall

• Table For Set-Up Support

Additional Information:

• Item Code: SHt-01
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden carrots are used for Packaging .

Approx. Rs 70,000 / PieceGet Latest Price

DESCRIPTION :

The setup consists of a brass tube fitted in a rectangular duct in a vertical position. The duct is open at the top and bottom, and forms an enclosure that serves the purpose of undisturbed surrounding. One side of the duct is fitted with a transparent acrylic window for visualization. An electric heating element is kept in the vertical tube that in turns heats the tube surface. The heat is lost from the tube to the surrounding air by natural convection. The temperature of the vertical tube is measure by temperature sensors and displayed by a Digital Temperature Indicator with multi-channel switch. The heat input to the heater is measured by a Digital Ammeter and a Digital Voltmeter and is varied by a variac. The tube surface is polished to minimize the radiation losses.

EXPERIMENTATION :

• To determine average heat transfer coefficient under natural convection.

Additional Information:

• Item Code: SHT-10
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden Carrots are used for Packaging

Approx. Rs 40,000 / PieceGet Latest Price

Approx. Rs 44,000 / PieceGet Latest Price

• Highly efficient
• Controlled temperature and dimensions
• Blackened surface

• Determination Of The Emissivity Of A Test Plate
• Study The Variation Of Emissivity Of Test Plate With Absolute Temperature

• With standard make on/off switch, mains indicator etc
• Instruction manual: an english instruction manual will be provided along with the apparatus
• Cabinet to accommodate the slab assembly with front window of glass/acrylic
• The whole set-up is mounted on a powder coated base plate
  

Additional Information:

• Item Code: SHT-11
• Production Capacity: 100 units/month
• Delivery Time: 5-8 days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

• To Determine The Overall Heat Transfer Co-Efficient For Various Degree Of Agitation.
• To Make A Comparative Study Of Heat Transfer Through Jacket & Coil In An Agitated Vessel

• Water Supply 20 Lit/Min (Approx.) And Drain

Additional Information:

• Item Code: SHT-18
• Production Capacity: 100 units/month
• Delivery Time: 10 days
• Packaging Details: wooden carrots are used for Packaging if required .

Approx. Rs 75,000 / PieceGet Latest Price

Approx. Rs 43,000 / PieceGet Latest Price

• To determine average surface heat transfer coefficient for a pipe by forced convection.
• Comparison of heat transfer coefficient for different airflow rates and heat flow rates.
• To plot surface temperature distribution along the length of pipe.

Additional Information:

• Item Code: SHT-09
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A,Other
• Packaging Details: wooden carrots are used for Packaging if required .

Approx. Rs 70,000 / PieceGet Latest Price

• Determination of stefan boltzmann constant
• Study the effect of hemisphere temperature on it

• Table For Set-Up Support

Additional Information:

• Item Code: SHT-12
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden carrots are used for Packaging if required .

Approx. Rs 70,000 / UnitGet Latest Price

• The main object of the experimental setup is to study the following at various flow rates
• Heat transfer rate
• Overall heat transfer co-efficient

• System: water to water (1 – 2 shell & tube type)
• Shell: material stainless steel insulated with ceramic wool and cladded with aluminum foil
• 25% cut baffles at 100 mm distance 4 nos
• Tube: od 16mm approx, length 500mm (24 nos )
• Water flow measurement: rota meters (2nos ) one each for cold & hot fluid
• Hot water tank: made of stainless steel insulated with ceramic fibre wool
• Hot water circulation: magnetic pump
• Instruction manual: an english instruction manual will be provided along with the apparatus
• A good quality painted rigid ms structure is provided to support all the parts.

• Water Supply 20 Lit/Min (Approx ) And Drain

Additional Information:

• Item Code: SHT-15
• Production Capacity: 100 units/month
• Packaging Details: wooden Carrots are used for Packaging

Approx. Rs 89,000 / PieceGet Latest Price

• Temperature sensors
• High efficiency
• Bears pressure

• To Calculate The Lmtd
• To Find Heat Transfer Rate
• To Find Out Overall Heat Transfer Co-Efficient

• To Calculate The Lmtd
• To Find Heat Transfer Rate
• To Find Out Overall Heat Transfer Co-Efficient

Additional Information:

• Item Code: SHT-16
• Production Capacity: 100 units/month
• Delivery Time: 5-8 days
• Packaging Details: wooden carrots are used for Packaging if required .

Approx. Rs 70,000 / PieceGet Latest Price

• To Determine The Overall Heat Transfer Co-Efficient And Film Co-Efficient For Vertical And Horizontal Condenser

• Water Supply 20 Lit/Min (Approx) And Drain

• System: Steam To Water
• Condensers: 2 Nos (Vertical & Horizontal) Insulated By Ceramic Wool And Cladding By Aluminium Foil
• Condensate Measurement: Measuring Cylinder & Stopwatch
• Water Flow Measurement: Rotameter
• Steam Generator: Made Of Stainless Steel Fitted With Level Indicator, Pressure Gauge, Safety Valve, Drain And Insulated With Ceramic Wool & Cladding With Aluminium Foil.
• Heaters: Nichrome Wire Heater (2 Nos)
• Control Panel Comprising Of
• With Standard Make On/Off Switch, Mains Indicator Etc
• Instruction Manual: An English Instruction Manual Will Be Provided Along With The Apparatus
• A Good Quality Painted Rigid Ms Structure Is Provided To Support All The Parts.

Additional Information:

• Item Code: SHT-17
• Production Capacity: 100 units/month
• Packaging Details: Wooden Boxes are used for Packaging if required

Approx. Rs 70,000 / PieceGet Latest Price

• To Concentrate A Solution And To Evaluate The Following At Steady State
• Material And Heat Balance
• Economy And The Capacity Of The Evaporator
• Overall Heat Transfer Co-Efficient

• Water Supply 5 Lit/Min (Approx) And Drain
• Required Chemicals

• Evaporator: Material Stainless Steel
• Shell Dia - 75mm, Length - 750mm,
• Tubes Dia - 12mm, Length - 750mm
• Feed Circulation: By Gravity Feed
• Feed Tank: Material Stainless Steel, Capacity 25 Ltrs
• Flow Measurement: Rotameters (One Each For Feed & Cold Water)
• Steam Generator: Made Of Stainless Steel Provided With Pressure Gauge & Level Indicator, Safety Valve And Drain Etc & Insulated With Ceramic Wool And Cladding With Aluminium Foil
• Piping: Stainless Steel And Pvc, Size ¼”
• Condenser: Shell & Tube Type Made Of Stainless Steel
• Bottom Product Tank: Made Of Stainless Steel, Capacity 10 Ltrs
• Water Supply Tank: Made Of Stainless Steel, Capacity 50 Ltrs For Condenser
• Pump: Fhp Capacity
• Heaters: Nichrome Wire Heater
• Control Panel Comprises Of: Digital Temp Controller: 0-19990c, (For Steam Generator)
• Digital Temp Indicator: 0-19990c, With Multi-Channel Switch
• Temp Sensors: Rtd Pt-100, Standard Make On/Off Switch, Mains Indicator Etc
• Instruction Manual: An English Instruction Manual Will Be Provided Along With The Apparatus
• The Whole Set-Up Is Well Designed And Arranged On A Good Quality Painted Structure.

Additional Information:

• Item Code: SHT-22
• Production Capacity: 100 units/month
• Delivery Time: 10 days
• Packaging Details: Wooden Carrots are used for Packaging if Required

Approx. Rs 57,000 / UnitGet Latest Price

The apparatus consists of fabricated SS shell, inside which SS tubes are fitted. Hot water passes to one end through the tubes and exit to another end. The cold water is admitted at the one end of shell, which passes over the hot-water tubes. The tubes are arranged in the shell so that the flow of cold and hot fluid crosses each other to make it cross flow. Valves are provided to control the flow rates of hot and cold water. Flow rates of hot and cold water are measured using Rotameters. A magnetic drive pump is used to circulate the hot water from a re-cycled type water tank, which is fitted with heaters and Digital Temperature Controller. Cold water is to be supplied by laboratory overhead tank by end user.

Experimentation:

• The main object of the experimental setup is to study the following at various flow rates: LMTD.
• Heat transfer rate
• Overall Heat Transfer Co-efficient.

Utilities Required:

• Water supply 20 lit/min (approx.) at constant head condition Floor Drain.

Additional Information:

• Item Code: SHT-29
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden carrots are used if required

Approx. Rs 70,000 / PieceGet Latest Price

• To demonstrate the super thermal conductivity of heat pipe and to compare its working with best
• Conductor i.E. Copper pipe & stainless steel pipe as same material of construction
• To plot the temperature v/s time response of pipes
• To plot the temperature distribution along the length of pipes

• Table For Set-Up Support

• Pipes : 1st : Heat Pipe Made Of Stainless Steel
• 2nd: Made Of Copper
• 3rd: Made Of Stainless Steel
• Heat Sink: Material Stainless Steel
• Working Fluid In Heat Pipe: Distilled Water
• Heaters: Nichrome Wire Band Type

Additional Information:

• Item Code: SHT-03
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A,Other
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden carrots are used for Packaging if required .

Approx. Rs 70,000 / PieceGet Latest Price

Evaporation deals with the concentration of a non-volatile solute from a solution by the removal of required amount of volatile solvent. Usually the solvent is water. By vaporizing a part of the solvent, useful product i.e. the concentrated solution or thick is produced and the vapor is discarded. Long tube evaporators are usually used for the concentration of foamy liquids. The set-up is consists of two evaporators fitted in series. Each is made up of Stainless Steel tubes surrounded by a Stainless Steel jacket and fitted with accumulator. Dilute solution is feed to the first evaporator. Steam from a steam generator is supplied to evaporator to concentrate the dilute feed solution to a desired level. The jacket is fitted with a steam trap and the condensate is collected at the end of trap. The vapours of volatile solvent produced in first evaporator are supplied to the second evaporator. The vapors of volatile solvent are condensed in a shell & tube type condenser and the balance non-volatile solute collected in the accumulator is recycled through the evaporator.

Experimentation:

• To concentrate a solution and to evaluate the following at steady state
• Material and Heat Balance.
• Economy and the capacity of the evaporator for different feeding arrangement.
• Overall heat transfer co-efficient
• To Study single effect and double effect evaporator Phenomenon

Utilities Required:

• Water Supply & Drain.
• Floor Area 2.5 m x 1.0 m
• 2 CFM for compressed air supply.
• Chemicals Sodium carbonate & distilled water.

Additional Information:

• Item Code: SHT-23
• Production Capacity: 100 units/month
• Delivery Time: 15-20 days
• Packaging Details: Wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

• To Determine The Overall Heat Transfer Co-Efficient Under Unsteady State Conditions At Different Temperatures
• To Determine The Heat Transfer Co-Efficient At The Boiling Point

• Water Supply
• Drain
• Required Chemicals

Additional Information:

• Item Code: SHT-20
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A,Other
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden carrots are used for Packaging if required .

Approx. Rs 70,000 / PieceGet Latest Price

The setup is designed to study the heat transfer in a pin fin. It consists of pin type fin fitted in a duct. A fan is provided on one side of duct to conduct experiments under forced draft conditions. Air flow rates can be varied. A heater heats one end of fin and heat flows to another end. Heat input to the heater is given through Variac. Digital voltmeter and digital ammeter are provided for heat measurement. Digital Temperature Indicator measures temperature distribution along the fin.

Experimentation:

• To study temperature distribution along the length of fin in both Free & forced convection.
• Comparison of theoretical temperature distribution with that of experimentally obtained distribution.

Utilities Required:

• Table for set-up support.

Technical Details:

• Fin: Pin type.
• Material: Brass.
• Size: 12.5 mm (approx.) 15 cm. long (approx.).
• Duct: Made of MS.
• Fan: Standard makes.
• Heater: Band type, Nichrome Wire.

• Dimmer stat: 0-230 V, 2 Amp.
• Digital Temp. Indicator: 0-3000C, with multi-channel switch
• Temperature Sensors: RTD PT-100 type.5 for pin and 1 for duct temperature. With standard make On/Off switch, Mains Indicator etc.

Additional Information:

• Item Code: SHT-08
• Production Capacity: 100 units/month
• Delivery Time: 5-8 days
• Packaging Details: wooden carrots are used for packaging if required

Approx. Rs 53,000 / PieceGet Latest Price

The bench-mounting equipment includes a vertical duct that holds the chosen heat transfer surface and all instruments needed. It include three different common heat transfer surfaces with the equipment: A Flat Plate. A Pinned Surface – similar to a tubular heat exchanger. A Finned Surface – similar to the fins on air-cooled engines or electrical heat sinks Each surface has its own built-in variable-power electric heater. Students choose which surface they need to test and fit it to the duct using simple fixings. For free convection tests, the heated air rises from the surface and up the duct. For forced convection tests, a variable-speed fan draws air up through the duct and across the surface. Thermocouples measure the air temperature upstream and downstream of the surface and the temperature at the heat transfer surface. The downstream probe moves in a traverse mechanism to measure the temperature distribution across the duct, allowing calculation of the bulk outlet temperature. An additional probe allows students to measure the temperature distribution along the extended surfaces of the pinned and finned heater transfer surfaces. A digital display shows the heater power and the temperatures measured by the thermocouples.

Experiments:

• Comparing free and forced convection for different surfaces
• Comparison of free convection from vertical and horizontal (finned) surfaces
• Comparison of heat transfer surface efficiency
• Comparing the coefficient of heat transfer
• Temperature distribution along finned and pinned surfaces

Technical Specifications:

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A,Other
• Production Capacity: 30
• Delivery Time: 10-15 days
• Packaging Details: wooden boxes

Approx. Rs 71,000 / PieceGet Latest Price

The apparatus is designed and fabricated according to the guarded Hot Plate Principle. It is a steady state absolute method suitable for materials, which can be laid, flat between two parallel plates and can be adopted for loose fill materials which can be filled between such plates.The heater plate is surrounded by a heating ring for stabilizing the temperature of the primary heater and to prevent heat loss radially around its edges. The cooling chamber is a composite assembly of grooved aluminum casting and aluminum cover with entry and exit adaptors for water inlet and outlet.

Technical Specifications:

• Ring guard heater: Width 35 mm sandwiched between Brass rings
• Cooling chamber: Made of Aluminium for water circulation, 2 Nos.
• Insulation: Ceramic wool blanket

• Dimmerstats: Range 0-230 V, 2 A, (2 Nos.) One each for central & ring guard heater.
• Digital Temperature Indicator: Range = 0-200°C, with multi-channel switch
• Temperature sensors: RTD PT-100 type ( 6 Nos)
• With standard make on off switch, Mains Indicator etc. MS Cabinet to accommodate the slab assembly. The whole setup is mounted on a powder coated base plate.

Additional Information:

• Item Code: SHT-28
• Production Capacity: 100 units/month
• Delivery Time: 5-8 days
• Packaging Details: wooden carrots are used for packaging if required

Approx. Rs 67,000 / PieceGet Latest Price

• To calculate the following parameters both ftor parallel and counter flow arrangement
• Rate of heat transfer lmtd
• Iii overall heat transfer co-efficient
• To compare the performance of parallel and counter flow heat exchanger.
  

Additional Information:

• Item Code: SHT-14
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A,Other
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden carrots are used for Packaging if required .