Mass Transfer Lab Equipment

Approx. Rs 70,000 / PieceGet Latest Price

The set up consists of a column fitted with perforated plates. Liquid is fed at the top of the column through distributor. The solute gas and air are measured separately, mixed in a mixing chamber and then passed through the perforated plates vertically upward and absorbed in liquid. All the flow rates can be independently varied to simulate different conditions. Liquid Sample can be taken out from the bottom of the column for analysis.

Experimentation:

• To study absorption of CO2 in aqueous NaOH solution in a sieve plate column.
• To determine the gas phase mass transfer co-efficient, KG a

Utilities Required:

• Water Supply
• Floor Drain.
• CO2 cylinder with control valve, pressure regulator and Pressure gauges
• Required Chemicals & Laboratory Glassware.

Additional Information:

• Item Code: SMT-11
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

The set up consists of a glass column. Water is fed at the top of the column along the walls to make the column a wetted wall column. Hot air from heating chamber with known humidity is allowed to pass through the column vertically upward and evaporation in the liquid film around the wall takes place. The flow rates of water and air can be independently varied to simulate different conditions. Instrumentation is provided to measure the dry and wet bulb temperatures at air inlet and outlet. 

EXPERIMENTATION :

• To determine the gas film coefficient in a wetted wall column using air-water system. 
• To find the mass transfer coefficient

Additional Information:

• Delivery Time: 2-3WEEK
• Packaging Details: CUSTOMIZE

Approx. Rs 70,000 / PieceGet Latest Price

DESCRIPTION:
The basic data of any distillation problem are the equilibrium between the liquid and vapours phases of the system subjected to distillation. Hence is of great importance to study the vapourliquid equilibrium. The set-up consists of distillation still with a heating element. An electrical Dimmer stat is connected to heating element for varying heat input. The vapours form the top of column is condensed in the shell and tube typecondenser by circulating cooling water. The condensate is collected in reflux drum and feedback to column as reflux. A tank with pump is provided to circulate cold water to condenser. Flow rates can be regulated through control valve fitted.
Instrumentation is provided to measure the temperatures at different points.

  EXPERIMENTATION:

Ø To determine the vapour Liquid Equilibrium curve for CCl4 and Toluene or any other mixture.

 U UTILITIES REQUIRED:

Ø Water Supply.

Ø Drain.

Ø Electricity Supply : 1 Phase, 220 V AC, 1.5 kW.

Ø Refractrometer for Analysis.

Ø Required Chemicals

TECHNICAL DETAIL:

Ø Distillation still : 1 Ltrs. Capacity, made of Stainless Steel.
Insulated by ceramic wool.

Ø Condenser : Concentric Tube type.

Ø Heater : Nichrome wire

Ø Cooling Water Tank : Material Stainless Steel , Capacity 15 Ltrs. Approx.

Ø Cold Water circulation : Using FHP Pump.

Ø Temperature Sensors : RTD PT-100 type

Ø Control panel comprising of
Digital Voltmeter: 0-300 Volt.
Dimmerstat : 0-230 V, 2A.
Digital Temp. indicator: 0-199.90C RTD PT-100 Type with multi-channel switch
With standard make on/off switch, Mains Indicator etc.

Ø Instruction Manual : An ENGLISH instruction manual will be provided along
with the Apparatus

Ø The whole set-up is mounted on a powder coated base plate.

Additional Information:

• Item Code: SMT-23
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

The set up consists of a glass column packed with Rasching rings. Liquid is fedat the top of the column through distributor. The solute gas and air are measured separately, mixed in a mixing chamber and then passed through the packed column vertically upward and absorbed in liquid. All the flow rates can be independently varied to simulate different conditions. Liquid sample can be taken out from the sampling point at the bottom of the column for analysis.

Experimentation:

• To determine the number of transfer units, Height of transfer unit and overall mass transfer co-efficient for the given system.

Utilities Required:

• Water Supply
• Floor Drain.
• CO2 cylinder with control valve, pressure regulator and Pressure gauges
• Required Chemicals & Laboratory Glassware.

Additional Information:

• Item Code: SMT-12
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

The apparatus consists of a forced draught, counter flow type cooling tower. Cooling air is supplied by a blower. Air enters the tower at the bottom. Hot water is obtained from a water heater. Hot water is sprayed over the mesh packing through the nozzles and it flows down wards. Evaporative cooling of water occurs due to the current of air and water gets cooled. The student can study the operation of cooling tower and calculate the energy balance.

Additional Information:

• Item Code: SMT-25
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 25,000 / PieceGet Latest Price

Approx. Rs 70,000 / PIECEGet Latest Price

The set-up consists of a glass column packed with Rasching rings. Continuous counter current contacts between the solvent and solute phases are made, which results into extract and raffinate streams. Flow meters (Rotameters) are used to note the flow of solvent & solute respectively. The continuous and dispersed phase streams are metered and derived from separate containers. The total set-up is housed in a well-designed rigid structure. The structure also supports tanks, piping, Rotameters, panel and other units.

Experimentation:

• To determine overall mass transfer co-efficient based on continuous & dispersed phase.
• To determine individual “Height of Transfer Unit” based on continuous & dispersed phase.

Utilities Required:

• Water Supply
• Drain.
• Required Chemicals & Laboratory Glassware

Additional Information:

• Item Code: SMT-01
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

Confirming a packed bed of spherical balls of a solid in a vertical tube, and observing its rate of diffusion into stream of air passed across the top of the tube can conveniently study the diffusion of solid into air. The equipment is fitted with a vertical glass column with a mesh near the base of column to hold the spherical balls. Spherical balls of known weight and diameter are filled in the column to make a packed bed. Air is allowed to pass through the silica gel chamber. From the bottom of the column, dry air is allowed to enter in the packed bed.

Experimentation:

• To calculate the mass transfer co-efficient of vaporization of naphthalene in air using a packed bed of spherical particles of naphthalene.
• To plot Sh/Sc 1/3 Vs Re on log 45g graph and determine the functional relationship.

Utilities Required:

• Compressed Air Supply at 2 Bar, 4 CFM.
• Weighing Balance 0.01 gm resolution.
• Solid Spherical Balls of Naphthalene
• Table for setup support.

Technical Detail:

• Diffusion Column: Material Borosilicate Glass
• Air flow Measurement: By Rotameter.
• Instruction Manual: An ENGLISH instruction manual will be provided along with the Apparatus
• The whole set-up is mounted on a powder coated base plate

Additional Information:

• Item Code: SMT-15
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

Using a small sample of the liquid in a narrow vertical tube, and observing its rate of evaporation into stream of air passed across the top of the tube can conveniently be used to study the diffusion of vapour of a volatile liquid into air. The set up consists of a glass tube placed in a water bath. A horizontal glass tube is fixed to the upper end of the tube and air is drawn through this by a small air pump included within the unit. Air flows over thistube maintaining partial pressure difference. A Traveling microscope with sliding vernier scale is provided to measure the rate of fall of solvent within capillary. A stirrer is fitted to maintain constant temperature inside the bath.

Experimentation:

• Determination of the diffusion co-efficient of an organic vapour in air.
• To study the effect of temperature on diffusion co-efficient.

Utilities Required:

• Required Chemicals & Laboratory Glassware.
• Table for setup support.

Additional Information:

• Item Code: SMT-14
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

Rotary dryer is a unit in which drying is done by forced draft action created by hot air. The set-up consists of a long revolving cylindrical shell slightly inclined towards the outlet. The shell is fitted with two brackets for support. Air from a blower passes through a heating chamber serves the purpose of drying agent. An arrangement for rotating the dryer shell at low RPM is provided by means of an electrical motor and a reduction gearbox.Wet feed enters from one end of the cylinder and dry material discharges from the other end. As the shell rotates internal flights lift the solids and shower them down through the interior of the shell. This action increases the contact of wet solid against hot air making the dryer very effective. The flow of hot air is counter-current to solids. Flow control and by-pass valve are fitted to regulate the airflow.

Experimentation:

• To study the operation of a Rotary Dryer.
• To study the drying characteristics of a solid material under batch drying condition in a rotary dryer.

Utilities Required:

• Wet Solid.

Additional Information:

• Item Code: SMT-18
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A,Other
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

This setup is designed to study the performance characteristics of solvent extraction of a particular component from a packed bed of solid material. The apparatus allows study of such systems as water/inorganic salts, water/sugar bed, methylene chloride/vegetable oil etc. The glass column is fitted with SS mesh to support the solid material. The solvent is introduced near the bottom of the column and it flows upward counter-currently to the solids. A pump supplies the solvent and flow rate is monitored by means of a Rotameter. Solvent feed tank is kept in a bath fitted with heater and digital temperature controller is used to maintain the constant temperature.

Experimentation:

• To study the effect of various system parameters like, solvent temperature, solvent rate and particle size on the %age recovery of oil from solid.

Utilities Required:

• Solid:10kg
• Solvent: 30ltrs
• Table for setup support

Additional Information:

• Item Code: SMT-04
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

The equipment consists of jacketed pressure vessel for distillation. Steam from a steam generator can either be allowed to enter in the outer jacket or in the vessel. The vapours form the top of the vessel are condensed in the shell and tube type condenser by circulating cooling water, supplied by laboratory overhead tank. The condensate is colleted in a separating chamber. The set-up is fitted with steam trap, control valves, pressure gauge, temperature sensors and other instrumentations required.

Experimentation:

• To study the characteristics of Steam Distillation.
• Efficiency of simple steam distillation set-up

Additional Information:

• Item Code: SMT-09
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

DESCRIPTION:

This setup is designed to study the performance characteristics of solvent extraction of a particular component from a packed bed of solid material. The apparatus allows study of such systems as water/inorganic salts, water/sugar bed, methylene chloride/vegetable oil etc. The glass column is fitted with SS mesh to support the solid material. The solvent is introduced near the bottom of the column and it flows upward counter-currently to the solids. A pump supplies the solvent and flow rate is monitored by means of a Rotameter. Solvent feed tank is kept in a bath fitted with heater and digital temperature controller is used to maintain the constant temperature.

EXPERIMENTATION:

Ø To study the effect of various system parameters like, solvent temperature, solvent rate and particle size on the %age recovery of oil from solid.

UTILITIES REQUIRED:

Ø Solvent: 30ltrs.

Ø Solid:10kg

Ø Table for setup support

TECHNICAL DETAIL:

Ø Extraction Column: Material Borosilicate Glass

Ø Solvent Flow Measurement: Rotameter.

Ø Solvent Tank: Made of Stainless Steel, Capacity 30 Ltrs. Double wall.

Ø Solvent circulation: Magnetic Pump made of Polypropylene to Circulate solvent.

Ø Heater: Nichrome wire heater

Ø Temperature Sensor: RTD PT-100 Type.

Ø Control panel comprises of: Digital Temp. Controller: 0-199.9°C (For Hot Water Bath) With Standard make on/off switch, Mains Indicator etc.

Ø Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus

Ø The whole setup is mounted on a powder coated base plate.

Additional Information:

• Item Code: SMT-05
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

Additional Information:

• Item Code: SMT-13
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 80,000 / PieceGet Latest Price

Additional Information:

• Item Code: SMT0-05
• Delivery Time: 2-3WEEK
• Packaging Details: CUSTOMIZE

Approx. Rs 70,000 / UnitGet Latest Price

• To study the fluidized bed drying
• To plot the drying curve under fluidized bed condition

• Granular and free flowing solid of size 1 to 2 mm

• Column: material borosilicate glass.
• Cyclone separator: material stainless steel, compatible capacity with collector.
• Air circulation: by forced draft fan, arrangement is done to vary the air flow rate.
• Heating chamber: compatible capacity.
• Heater: nichrome wire heater.
• Temperature sensors: rtd pt-100 type.

• Digital temp controller: 0 1999°c (for hot air)
• Standard make on/off switch, mains indicator etc

Additional Information:

• Item Code: SMT-19
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

• To Study The Drying Characteristics Of A Solid Material Under Batch Drying Condition
• Determination Of Drying Rate And To Plot Moisture Lost With Time Under For Different Operating Conditions

Additional Information:

• Item Code: SMT-16
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

This is a dryer in which moisture removal takes place by means of forced draft action created by hot air. The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to a electronic weighing balance, which is fitted on the bottom, outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from a blower passes through a heating chamber and is used as drying agent. Arrangement is done to vary the airflow rate.

Experimentation:

• To study the drying characteristics of a solid under forced draft condition and determine the critical
• moisture content.
• To correlate the constant drying rate with air mass velocity.

Utilities Required:

• Wet Solid.

Additional Information:

• Item Code: SMT-17
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

The experimental set-up of Spray Tower consists of a glass column provided with necessary accessories. It operates on a semi-batch mode. Fine spray nozzle is fitted at the top. Feeds are metered by Rotameters and derived from separate feed tanks. The liquid-liquid interface can be maintained by controlling the flow rate of extract with the help of needle valve provided on Rotameter. Total set-up is housed in a rigid structure. The structure also supports tanks, piping, Rotameters and other unit.

Experimentation:

• To study the effect of the dispersed phase flow rate on overall volumetric mass transfer coefficient.
• Dispersed phase hold-up study.

Utilities Required:

• Drain.
• Required Chemicals & Laboratory Glassware.

Additional Information:

• Item Code: SMT-03
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/A
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

DESCRIPTION :

EXPERIMENTATION:

Ø To study the performance of a Batch Crystallizer.

UTILITIES REQUIRED :

Ø Water Supply.

Additional Information:

• Item Code: SMT-20
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden boxes are used.

Approx. Rs 70,000 / PieceGet Latest Price

DESCRIPTION:

The column is made of Stainless Steel with seven plates for mounting the bubble caps. Each plate is provided with one bubble cap. An electrically heated reboiler is installed at the bottom of the column. The bottom product is collected in the tank. The vapours form the top of column are condensed in the shell and tube type condenser by cooling water supplied by laboratory overhead tank. The condensate is divided into reflux and distillate by automatic reflux divider and R/D Ratio can be varied. Reflux is fed back to the column and distillate is received in a receiving tank. The complete column is insulated for minimizing the heat loss. Instrumentation provided for pressure & temp. measurement wherever necessary.

EXPERIMENTATION:

Ø  To estimate the batch distillation curves for a binary system and verify the binary batch distillation equation for a known number of theoretical plates.

Ø  To operate the column under total reflux condition and estimate the minimum number of theoretical plates required

UTILITIES REQUIRED :

Ø  Water Supply 2 LPM at 5 m head.

Ø  Drain.

Ø  Electricity Supply: 1 Phase, 220 V AC, 6 kW.

Ø  Required Chemicals.

Additional Information:

• Item Code: SMT-06
• Production Capacity: 100 units/month
• Delivery Time: 10-15days
• Packaging Details: Wooden boxes are used.