Electrical Lab Equipment

Approx. Rs 28,000 / PieceGet Latest Price

Product BrochureProduct Details:

Electromechanical Energy Conversion Lab

• D.C. Shunt Generator Magnetization Characteristics
• D.C. Compound Generator Characteristics
• D.C. Shunt Motor Speed-Torque Characteristics
• Speed Control of D.C. Shunt Motor
• Swinburne’s Test on D.C. Shunt Motor
• Hopkinson’s Test on D.C. Shunt Motor
• B-H Curve Apparatus
• Sumpner’s Test on 1 Phase Transformer
• O.C. and S.C. Tests on 1 Phase Transformer
• O.C. and S.C. Tests on Alternator
• Three Phase to Two Phase Conversion Apparatus
• 1 Phase and 3 Phase Transformer Polarity & Ratio Tests
• No Load & Block Rotor Test on 1 Phase Induction Motor
• No Load & Block Rotor Test on 3 Phase Induction Motor
• V-Curve of a Synchronous Motor
• Synchronization of an Alternator

Approx. Rs 10,000 / PieceGet Latest Price

Product BrochureProduct Details:

We offer Electrical Measurement Lab Equipment to our clients.

Other Details:

• Lissajous Figure Apparatus
• Kelvin’s Double Bridge
• Maxwell’s Bridge
• Hay’s Bridge
• Anderson’s Bridge
• Owen’s Bridge
• De Sauty Bridge
• Schering Bridge
• Frequency and Differential Time Counter Apparatus
• LCR Bridge Apparatus
• Power Power Factor Measurement Apparatus
• Distortion Factor Meter
• Temperature Transducer
• Pressure Transducer
• Transistor Tester Kit
• Semiconductor Diode Voltmeter

Approx. Rs 75,900 / UnitGet Latest Price

Product BrochureProduct Details:

DESCRIPTION:
This is for estimating the bearing capacity of shallow foundations in situ and for the design of flexible pavement. In the test procedure a steel plate is subjected to gradually increasing load and settlements of the plates recorded. Maximum bearing capacity is noted as that load at which the plate starts sinking rapidly. SPECIFICATIONS:
The basic outfit consists of : 50 tone Hydraulic jack with separate pumping unit fixed to a 0- 500KN x 0.5KN. Pressure gauge and flexible metal piper 5 mtr long- 1No. Special ball and socket arrangement between the jack and the bearing plate-1No. Extension rod 12mm. dia. x 25cm. long for taking dial gauge readings-16 Nos. Magnetic base with female thread on top for holding extension rod-4Nos. Top end plate, 50mm, dia. with male thread for fitting onto the extension rods and positioning the dial gauge plinger-4Nos. Column 15cm. dia. x 25cm long with flanges complete with four bolts and nuts- 2Nos. Column 15cm. dia. x 50cm long with flanges complete with four bolts and nuts- 1Nos. Bridge support of welded steel angel construction, 5mtr. Span and stands approximately 30cm, high, fitted with two quick release clamps a for positioning and holding the dail bracket-2Nos. Plane M.S. Plate 60cms x 60cms. Square x 25mm thick plane M.S. Plate 45cmx square x 25mm thick plane M.S. Plate 30cms x 30cmx square x 25mm thick Dial Gauge 0.01mm x 25mm- 4Nos.
ACCESSORIES:

Plane M.S. Plate 75cm x 25mm thick plane M.S. Plate 50cmx 25mm thick Grooved M.S Plate 60cms x 60cms x 25mm thick grooved M.S. Plate 45cms x 45cms x 25 mm thick Grooved M.S. Plate 30cms x30cms x 25mm thick Grooved M.S. Plate 75CMS x 75cms x 25mm thick.
NOTE:
1) When plates of size more than 30cm.sq are used in order to prevent deflections of the edge, a series of smaller plates are advised to be placed concentrically on the bottom plate.2) Flexible rubber pipe 1mtr. Length can be supplied for the hydraulic jack in place of metal pipe at extra cost. For site testing load trusses to meet the reaction of loading are avaiLable in different capacities as under.